Study Guide Instructor view
Packets and Packet Switching
Teaching notes for Lesson 4.1, with controls for presenting it.
Keep this page on your own screen. Share only the lesson window. The lesson window holds no teaching notes, so sharing it cannot show them.
Presenting
- Open the lesson in its own window and share that window, not this one.
- Use Next and Previous here, or the lesson’s own, to move through the lesson. Next reveals one thing at a time: the next idea, or the answer to the question on screen, then the next step. Previous takes the last reveal back. The line below says what is on screen and what Next will show.
- Reveal hints and answers when the class is ready, and reset a demonstration before using it again.
The controls need JavaScript and a browser that supports BroadcastChannel. Without them, open the lesson in presentation mode and use its own controls.
The two windows talk to each other only inside this browser, on this device. Nothing is sent to a server, and no account is needed. A second device (a phone or another tablet) cannot follow the lesson window yet.
Now on the lesson window
- On screen
- Next teaching point
Guidance for this point
Lesson plan
- Level
- Intermediate
- Time
- About 60 minutes; the steps below add up to 60
Learners plan how to post a 300-page story in six envelopes so that it can be reassembled, and discover for themselves that each envelope needs an address, a number and a return address. The same idea is then met on a network as packets with a header, payload and trailer, routers choosing routes one step at a time, packets arriving out of order, and the receiver rebuilding the message using packet numbers. The lesson ends by weighing advantages and disadvantages and explaining the whole process in the learner’s own words.
Objectives
- Explain why data is broken down into packets before it is transmitted
- Describe the structure of a packet: a header holding the destination address, packet number and originator’s address, then the payload, then the trailer
- Describe how packet switching works: each packet may take a different route, and a router controls the route
- Explain why packets may arrive out of order and how the receiving device puts them back in order
- Apply packets and packet switching to a new situation, such as a video message or a photo upload
Before the lesson
- Six envelopes or six sheets of paper, labelled by learners during the first step, to model the post office.
- Large cards for four packets of a short message so that learners can physically reorder them.
- A map on the board of the four routers A, B, C and D with the two roads B and C, to follow the four-packet journey.
- Make sure learners recall the word header from the earlier lessons; define the three header items only after they have suggested them.
Steps
Introduction Opening
On the lesson window now
On screen: the lesson’s title, module and number; Next adds its objectives and key terms, as the lesson page lists them; Next again begins the first step.
Objectives on screen
- Explain why data is broken down into packets before it is transmitted
- Describe the structure of a packet: a header holding the destination address, packet number and originator’s address, then the payload, then the trailer
- Describe how packet switching works: each packet may take a different route, and a router controls the route
- Explain why packets may arrive out of order and how the receiving device puts them back in order
- Apply packets and packet switching to a new situation, such as a video message or a photo upload
Purpose: Learners plan how to post a 300-page story in six envelopes so that it can be reassembled, and discover for themselves that each envelope needs an address, a number and a return address. The same idea is then met on a network as packets with a header, payload and trailer, routers choosing routes one step at a time, packets arriving out of order, and the receiver rebuilding the message using packet numbers. The lesson ends by weighing advantages and disadvantages and explaining the whole process in the learner’s own words.
1. A book that will not fit in one envelope Think 6 min
On the lesson window now
Purpose: Learners decide what must be written on each envelope so that a book sent in six parts can be put back together, before any network vocabulary is introduced.
Ask
- Maya splits the story into six envelopes. What should she write or include so that Daniel can put the story back together?
- What if What if an envelope cannot be delivered?
Responses to expect
- Daniel’s address, so the post office can deliver it
- A number such as ‘envelope 3 of 6’, so Daniel can order the pages and notice a missing one
- Maya’s own address, so that it can be returned or Daniel can reply
Misconceptions to challenge
- A learner may believe: “The envelopes will arrive in the order they were posted.” Respond: The vans take different roads and may arrive on different days or in a different order. That is why the number matters.
- A learner may believe: “Only the address is needed.” Respond: Ask Daniel how he would know which envelope is the first. The address says where, not which part.
On the board or with the pen
- Draw one envelope with three labelled fields: to, from and number; fill it in with learners’ suggestions.
Checking understanding: Pairs label their envelope and swap with another pair, who try to reorder a shuffled set of three envelopes.
Depending on the answers
- If learners omit the number: shuffle the sample envelopes and ask the class to put the pages back in order.
English as an additional language
- Check envelope, address and delivered; hold up an envelope and point to each field.
Discussion pause: Thirty seconds of silent thinking before the pairs share.
In the lesson window
- Think it through: Maya splits the story into six envelopes. What should she write or include so that Daniel can put the story back together correctly?
2. The same idea on a network Discover 8 min
On the lesson window now
Purpose: Learners transfer the envelope labels to a network and name the three header items, then use them to decide which part of the header puts packets in order.
Ask
- What are the three things a header holds, and which envelope field does each match?
- Six packets of a photo reach a phone in a different order. Which part of the header lets the phone put them in order?
Responses to expect
- Destination address, packet number and originator’s address
- The packet number, because it is different on every packet
Misconceptions to challenge
- A learner may believe: “The destination address shows where each packet belongs in the photo (which-header-item option A).” Respond: Every packet of this photo has the same destination address. Could it tell packet 2 from packet 5?
- A learner may believe: “The originator’s address shows which packet was sent first (option C).” Respond: All six packets came from the same sender, so they share that address. What would separate one packet from another?
- A learner may believe: “A packet is just a piece of the data.” Respond: A packet is data sent with information about where it is going and where it fits.
On the board or with the pen
- Write header: destination address, packet number, originator’s address; draw a link to the three fields on the envelope.
What learners should notice
- The two addresses are the same on every packet of a message; only the packet number differs.
Checking understanding: The which-header-item check; ask which field would differ if two packets were compared.
Depending on the answers
- If learners choose the destination address: put packets 2 and 5 side by side and ask which header item differs.
Support
- Give learners a labelled envelope diagram to compare with the header list.
In the lesson window
- Check your understanding: Six packets of a photo reach a phone in a different order from the one in which they were sent. Which part of the header lets the phone put them in the right order?
3. What is inside, and what ends the packet Explain 8 min
On the lesson window now
Purpose: Learners work out that a packet needs data and an end marker as well as a header, then name payload and trailer and sort items into the three parts.
Ask
- A packet cannot be only a header. What else must it contain? What might be useful at the very end?
- In which part of the packet is each of these items: the destination address, a slice of a photo, packet 4 of 9, a marker showing the packet has ended?
Responses to expect
- The actual data, and something that marks the end and lets the receiver check the contents
- Header, payload, header, trailer
Misconceptions to challenge
- A learner may believe: “The header and trailer are part of the user’s data.” Respond: Only the payload is the data the user wanted. The header and trailer are extra information the network needs.
- A learner may believe: “The trailer holds the destination address.” Respond: Delivery information has to be read first, so it is in the header. The trailer marks the end and carries checking information.
On the board or with the pen
- Draw one long box divided into header, payload and trailer, with the three header items listed above it.
Checking understanding: The sort-packet-parts table: watch for the originator’s address row, which is also header information.
Depending on the answers
- If learners cannot place the originator’s address: ask where the reply would be sent if it were not on the packet.
English as an additional language
- Teach payload as ‘what the packet carries’ and trailer as ‘the end of the packet’.
In the lesson window
- Think it through: A packet cannot be only a header: the header is just the label on the envelope. What else must a packet contain? And what might be useful at the very end of a packet?
4. Many roads between two towns Predict 8 min
On the lesson window now
Purpose: Learners predict whether packets arrive in the order they were sent, and meet routers and packet switching.
Ask
- Six packets leave a laptop in order 1 to 6 and the routers send them along different roads. Will they necessarily arrive in the order 1 to 6?
- What does a router read in a packet, and what does it decide?
Responses to expect
- No: a packet on a slow road can arrive after a later packet on a quicker road
- The destination address in the header; it chooses the next router on the way
Misconceptions to challenge
- A learner may believe: “Packets arrive in the order they were sent.” Respond: Think of two vans, one on a quiet road and one on a road with roadworks: the later van can arrive first.
- A learner may believe: “The sender plans the whole route in advance.” Respond: Each router chooses the next step for each packet, using what it knows of the network at that moment.
On the board or with the pen
- Draw two towns with three roads between them and trace two packets taking different roads.
Checking understanding: A show of hands: who thinks the order is guaranteed? Revisit after the four-packet journey.
Depending on the answers
- If most learners say order is guaranteed: run the van picture slowly with packets 1 and 2 on different roads.
English as an additional language
- Check router, route and junction; use a road junction as the picture for a router.
Discussion pause: Ask learners to write yes or no and a reason before anyone speaks.
In the lesson window
- Think it through: Six packets leave a laptop in order 1, 2, 3, 4, 5, 6, and the routers send them along different roads. Will they necessarily arrive in the order 1 to 6? Explain what might change the order.
5. Watching four packets travel Experiment 11 min
On the lesson window now
Purpose: Learners follow four packets through four routers, see them arrive out of order, and decide what the receiver does when packet 3 is late.
Ask
- Which router chooses the road for each packet, and why do packets 1 and 2 take different roads?
- The server has packets 1, 2 and 4, and packet 3 is still on its way. What does it do?
Responses to expect
- Router A chooses, depending on how busy each road is
- It waits for the last packet and then orders the payloads by packet number
Misconceptions to challenge
- A learner may believe: “The server rebuilds the file from packets 1, 2 and 4 straight away (packet-3-arrives-late option A).” Respond: The file would have a piece missing. What does the server need to have before it can put the payloads in order?
- A learner may believe: “The laptop must send the whole file again (option B).” Respond: That would waste the work already done. Packet 3 has not been lost, only delayed.
- A learner may believe: “A packet carries a map of its journey.” Respond: Each router reads only the destination address and decides the next step.
On the board or with the pen
- Draw the four routers and mark each packet’s road with a different colour as the step-through advances.
What learners should notice
- The arrival order is 1, 2, 4, 3, but the packet numbers still say where each belongs.
Checking understanding: The packet-3-arrives-late check.
Depending on the answers
- If learners suggest asking for the file again: ask how long the server should wait and what it would lose by repeating everything.
Stretch
- What could the server do if packet 3 never arrives? (Preview of the Error Detection lesson.)
In the lesson window
- Check your understanding: In the example, the server has packets 1, 2 and 4, and packet 3 is still on its way. What does the server do?
6. Rebuilding a message Apply 11 min
On the lesson window now
Purpose: Learners reorder packets by number using a worked example, rebuild a new message alone, and correct the idea that all packets must take one route.
Ask
- Packets arrive in the order 4, 1, 3, 5, 2. How do you rebuild the message?
- Priya says all packets of one file must take the same route or the file would arrive scrambled. What is wrong?
Responses to expect
- Sort by packet number, not by arrival: Library closes at five today
- Packets may take different routes; the packet numbers let the receiver rebuild the file in order
Misconceptions to challenge
- A learner may believe: “Different routes would give different file contents (priya-same-route option A).” Respond: The payloads are the same whichever road carries them. What in the header says where each one fits?
- A learner may believe: “The sender must tell the routers the route in advance (option B).” Respond: Does the sender plan the route? Think about who reads the destination address and chooses the next step.
- A learner may believe: “Only the payload goes along a route, with the header and trailer travelling separately (option D).” Respond: A packet travels as one unit. What does a router need the header for?
On the board or with the pen
- Write the five packets on cards in arrival order and reorder them with learners at the board.
What learners should notice
- The receiver waits until the last packet has arrived before it sorts.
Checking understanding: The rebuild table and the priya-same-route question, which has four options that each represent a different misunderstanding of routes.
Depending on the answers
- If learners rebuild by arrival order: ask them to read the packet numbers first and sort.
- If learners are fluent: ask what happens if packet 3 is damaged on the way.
Support
- Hand out the five packets as cards that can be physically reordered.
In the lesson window
- Apply it: Priya says: “All the packets of one file must take the same route. If they took different routes, the file would arrive scrambled.” What is wrong with Priya’s reasoning?
7. Why use packets at all? Consolidate 8 min
On the lesson window now
Purpose: Learners weigh the advantages and disadvantages of packet switching, apply it to a video message, and explain the whole journey in their own words.
Ask
- Give one advantage and one disadvantage of splitting data into packets and sending them by different routes.
- A video message of 400 packets loses packet 212 to damage. Why is this not a disaster?
- Explain how a photo gets from one phone to another, using packet, header, payload, router and packet number.
Responses to expect
- Advantages: traffic can go round a busy or broken router; only a damaged packet is sent again. Disadvantages: reordering takes time; header and trailer add extra data
- Only packet 212 needs sending again, because each packet has its own number
- A sequence from splitting, to header, to routers, to rebuilding by packet number
Misconceptions to challenge
- A learner may believe: “The whole video has to be sent again (video-message-apply option B).” Respond: Does the damage to one packet spoil the other 399? Think about what a packet number identifies.
- A learner may believe: “The header carries a copy of the payload, so the receiver can leave 212 out (option C).” Respond: The header holds addresses and a packet number, not the data. What would the video be missing without packet 212?
- A learner may believe: “Packet switching is always faster.” Respond: It shares the network and routes around problems, but it adds header data and the work of reordering.
Checking understanding: Listen for all five words of the explanation and the correct order of events.
Depending on the answers
- If learners leave out the packet number from the explanation: ask how the receiver knows where each payload fits.
- If learners are secure: ask them to compare with a phone call that keeps one line open (circuit switching, optional extension).
Stretch
- Why does sharing a network between many conversations waste less capacity than reserving a line for each?
In the lesson window
- Think it through: Give one advantage and one disadvantage of splitting data into packets and sending them by different routes. Think about a broken router, a damaged piece of data and the extra information on every packet.
- Apply it: A video message is sent in 400 packets. Packet 212 is damaged on the way, and the other 399 arrive safely. Which statement about packet switching explains why this is not a disaster?
- Think it through: In your own words, explain to someone who has not done this lesson how a photo gets from one phone to another across the internet. Use the words packet, header, payload, router and packet number.
Lesson recap Closing
On the lesson window now
On screen: the lesson’s objectives again; Next adds the closing question, which asks the class to explain each one in their own words without looking back. It says nothing about what anyone has learnt: use the answers to decide what to revisit.
Points to listen for
- Data is broken into packets. Each has a header (destination address, packet number, originator’s address), a payload (a slice of the data) and a trailer (the end and information for checking).
- In packet switching each packet may take a different route; a router reads the destination address and chooses the next step.
- Packets may arrive out of order; once the last one has arrived the receiver uses the packet numbers to put them in order.
- Only a damaged packet has to be sent again, and traffic can go round a busy router; the cost is extra header data and the work of reordering.
Consolidation
- Data is broken into packets. Each has a header (destination address, packet number, originator’s address), a payload (a slice of the data) and a trailer (the end and information for checking).
- In packet switching each packet may take a different route; a router reads the destination address and chooses the next step.
- Packets may arrive out of order; once the last one has arrived the receiver uses the packet numbers to put them in order.
- Only a damaged packet has to be sent again, and traffic can go round a busy router; the cost is extra header data and the work of reordering.